Whole House Repipe Cost A whole-house repipe is a major investment, and the number on your quote won't come from square footage alone. Pipe material, bathroom and fixture count, foundation type, pipe access, labor, permits, and wall or floor restoration all push the total up or down.

Two homes of the same size can land thousands of dollars apart. This guide covers planning-level cost ranges, what a quote should include, the hidden expenses people miss, and how to build a budget you can trust.

Key Takeaways

  • U.S. estimates typically run $1,500 to $15,000, with about $7,500 as a planning figure, not a quote.
  • Material, bathroom count, foundation, access, labor, permits, and restoration drive the price.
  • Slab foundations and multi-story homes cost the most.
  • An itemized, inspection-based quote beats a square-footage or phone estimate.

How Much Does a Whole House Repipe Cost? (Pricing Overview)

A repipe has no fixed price. Online ranges help you plan questions and compare estimates. They don't replace an onsite evaluation.

Misreading the cost causes real problems:

  • Underbudgeting, then delaying work that can't wait
  • Comparing quotes that cover different scopes
  • Finding permit, access, fixture, water-main, or restoration charges after work begins

Typical Cost Range

Angi's 2026 guide reports $1,500 to $15,000, with a typical cost near $7,500. Elsewhere on the same page it cites a professional range of $1,250 to $22,000.

Whole house repipe cost range and typical planning figure

These are editorial cost-guide estimates, not an audited national survey. The guide doesn't clearly separate supply-only work from drain work, and it doesn't define a standard home size.

Expect a quote to include:

  • New hot and cold supply lines and connections
  • Pressure testing
  • Basic access work

It may exclude:

  • Drain and sewer lines
  • Fixture or water-heater replacement
  • Painting and flooring
  • Water-main work

Always ask which items are in the base price.

Cost Tiers by Complexity

Smaller homes with one or two bathrooms, short pipe runs, and an accessible crawlspace or open wall routing sit at the low end. No reliable separate dollar range exists for this tier, so ask contractors to price your specific layout instead of relying on a number.

A standard whole-house repipe is the most useful comparison tier. Bathroom count, kitchen and laundry connections, total fixtures, and labor scope shape the quote. Angi puts labor at about 70% of the total, or around $5,250 on a typical job. That's why access and layout matter more than the pipe itself.

Several conditions push a job into high-complexity pricing:

  • Slab foundations, where piping under concrete is harder and costlier to reach
  • Multiple stories
  • Finished tile or flooring
  • Difficult wall access
  • Extensive corrosion or rerouting
  • Water-main replacement

Angi notes that larger and multistory homes with more fixtures cost more, though it gives no separate price for this tier.

Cost by Home Size, Bathrooms, and Layout

No reliable per-square-foot or per-bathroom price schedule exists. A 2,000-square-foot home with one bathroom and a straight run differs sharply from one with four bathrooms, long branch lines, and awkward routing. Compare quotes by fixture count, foundation, and access instead of square footage.

Key Factors That Affect the Cost of a Whole House Repipe

Pricing reflects material quantity, labor difficulty, code requirements, and restoration, not just the pipe.

Home Size, Bathroom Count, and Fixture Layout

Every bathroom, kitchen fixture, laundry connection, and hose bib adds branch lines, fittings, shutoffs, and labor. More fixtures means more time.

Foundation Type and Access

Crawlspace or raised-foundation homes allow easier routing. Slab homes often need new lines run through attics or walls. Angi confirms access under concrete is significantly more expensive but publishes no dollar premium, so ask each contractor how they'd route yours.

Pipe Material and Installation Method

Angi lists material-only costs per linear foot:

Material Price per linear foot
PEX $0.40 to $2
CPVC $0.50 to $1
Copper $2 to $8

PEX CPVC and copper repipe material cost comparison

PEX is flexible, resists corrosion and freezing, and uses fewer connections, so it's often lower in cost. Copper is time-tested and durable. Both work well, and the right choice depends on your home, water conditions, and priorities.

PEX products carry specific chlorine-resistance ratings, so PPI's technical note is worth a look if your water is heavily disinfected. Confirm which materials your local code allows.

Labor, Permits, and Local Requirements

Labor is usually the largest line item. Permits vary by city. Irvine, for instance, requires an application and plans for residential repipes, and San Francisco publishes its own plumbing fee schedule.

Check your local building department and confirm your plumber holds the right license. In California, that's a C-36 plumbing classification.

Wall, Floor, and Finish Restoration

Access openings need patching. Angi puts small drywall holes at $20 to $120, up to $300 for several, excluding retexturing and paint. Tile, flooring, and cabinet work can add more. Basic patching is not the same as full cosmetic restoration, so clarify which one you're getting.

Low-Cost vs High-Cost Whole-House Repiping: What's the Difference?

Factor Lower-cost approach Higher-cost approach
Access Minimal openings, patch only More openings, full finish work
Materials Basic grade, fewer extras Premium grade, better fittings
Disruption Faster, less protection More careful, more cleanup
Warranty Limited Longer, clearer terms

The lowest bid isn't automatically the best value. The California Contractors State License Board advises getting at least three written bids on identical scope and warns that a substantially low bid may omit work or signal substandard work.

Cost Breakdown of a Whole House Repipe

The total goes beyond the pipe itself. Break the quote into one-time, add-on, and periodic costs.

Initial Assessment and Materials

  • Inspection of existing plumbing, pressure, and pipe material
  • Routing plan for the new system
  • Pipe, fittings, and shutoff valves
  • Fixture connections
  • Removal or abandonment of old supply lines

Ask which of these appear in the base quote.

Installation, Access, Permits, and Testing

Labor typically covers:

  • Opening access points
  • Routing and securing new lines
  • Pulling permits and scheduling inspection
  • Pressure testing, flushing, and restoring water service

System Wide Services keeps wall openings as few and small as possible, and water is often back on by the end of the day.

Restoration and Additional Work

Itemize these before approving the job:

  • Patching and painting
  • Tile or flooring repair
  • Fixture or valve replacement
  • Water-main work
  • Unexpected corrosion or structural access issues

Ongoing and Periodic Costs

New supply lines cut repair calls but don't eliminate maintenance. Budget separately for future fixture shutoff replacement and periodic inspections, and read the warranty conditions. No reliable national price exists for these items, so ask your plumber.

How to Estimate the Right Budget for a Whole House Repipe

The right budget balances system condition, installation quality, code compliance, disruption, and long-term value, not just the lowest number.

Build a Home-Specific Project Profile

Gather this before requesting estimates:

  • Approximate size and number of stories
  • Bathroom and fixture count
  • Foundation type
  • Current pipe material
  • Symptoms such as pinhole leaks, rusty water, or low pressure
  • Past leak repairs and planned remodeling

Compare Itemized Quotes, Not Just Totals

Check each quote for:

  • Pipe type and grade
  • Fixture scope
  • Labor, permits, and testing
  • Access openings and drywall restoration
  • Water-main work
  • Exclusions, payment schedule, warranty, and change-order terms

Get multiple bids from licensed plumbers, all inspecting the same scope. System Wide Services offers upfront, flat-rate pricing and code-compliant work for homeowners in its Southern California service area across Los Angeles and Orange counties.

Calculate Repair-Versus-Repipe Value

Compare projected repair costs over a set period with a full repipe. Angi's repair data shows slab leak repair at $630 to $4,400, while standard pipe leak repair runs $250 to $850 per pipe. If you're repairing leaks every few months, those costs stack up. Still, one leak isn't an automatic reason to repipe. Get a professional assessment first.

Allow for Uncertainty and Financing

Set aside a disclosed contingency for concealed damage or scope changes. Ask your contractor what's reasonable for your home instead of using a generic percentage. For financing, compare options carefully. HELOC rates are typically variable, and failing to repay puts your home at risk. System Wide Services offers Wisetack financing, subject to credit approval.

What Most People Miss When It Comes to Whole House Repipe Cost

  • Upfront pipe price isn't the whole story. Labor, permits, access, restoration, fixture valves, and water-main work all add up.
  • The cheapest bid can cost more later. Confirm licensing, pipe grade, installation method, testing, warranty, and code compliance.
  • Premium isn't always better. Over-specifying materials may add little value, while under-specifying access and restoration leaves a cheap quote incomplete.

Conclusion

Repipe cost varies with layout, fixture count, material, foundation access, labor, permits, and restoration. The most useful number comes from an inspection and a clearly defined scope.

If you're dealing with recurring leaks, corrosion, poor pressure, or aging supply lines, compare itemized estimates from licensed professionals. Choose the one that balances reliability, compliance, and long-term value.

Frequently Asked Questions

How much do plumbers charge to repipe a house?

Published guides estimate $1,500 to $15,000, with about $7,500 typical. Home size, bathrooms, material, access, labor, permits, and restoration all shift your quote.

How much is it to repipe a 2000 square foot house with a slab foundation?

Square footage and slab construction alone don't set the price. Bathroom count, routing, access, material, and local permits matter more, so get an inspection-based quote.

What is the cheapest way to repipe a house?

Cost-efficient material and accessible routing reduce labor. Don't skip permits, testing, proper fittings, restoration, or qualified installation to save money.

How do they repipe your house?

A plumber inspects and plans, shuts off water, removes or abandons old lines, and installs new ones. Then they connect fixtures, pressure-test, pass inspection, clean up, and patch.

Should I repipe my house with PEX or copper?

PEX is flexible and often cheaper to install. Copper is long-proven and durable. Neither is universally best; water chemistry, code, and your priorities decide.

Is it worth repiping a house?

It can be when leaks recur, corrosion is widespread, or old pipe is failing. Get an inspection and compare repair costs against replacement first.